X5083PI datasheet(13/20 Pages) INTERSIL

13 / 20 page

FN8127.2

September 16, 2005

Absolute Maximum Ratings

Operating Conditions

Temperature Under Bias . . . . . . . . . . . . . . . . . . . . . .-65°C to 135°C

Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to 150°C

Voltage on Any Pin with Respect To Vss . . . . . . . . . . . . . -1.0V to 7V

D.C. Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA

Lead Temperature (Soldering, 10s) . . . . . . . . . . . . . . . . . . . . . 300°C

Temperature Range

Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C

Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C

VCC Range

-2.7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V

Blank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5V to 5.5V

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the

device at these or any other conditions above those indicated in the operational sections of this specification is not implied.

DC Electrical Specifications

(Over the recommended operating conditions unless otherwise specified.)

SYMBOL

PARAMETER

TEST CONDITIONS

LIMITS

UNIT

MIN

TYP

MAX

ICC1

VCC Write Current (Active)

SCK = VCC x 0.1/VCC x 0.9 @ 5MHz,

SO = Open

5mA

ICC2

VCC Read Current (Active)

SCK = VCC x 0.1/VCC x 0.9 @ 5MHz,

SO = Open

0.4

ISB1

VCC Standby Current WDT = OFF CS = VCC, VIN = VSS or VCC,

VCC = 5.5V

1µA

ISB2

VCC Standby Current WDT = ON

CS = VCC, VIN = VSS or VCC,

VCC = 5.5V

µA

ISB3

VCC Standby Current WDT = ON

CS = VCC, VIN = VSS or VCC,

VCC = 3.6V

µA

ILI

Input Leakage Current

VIN = VSS to VCC

0.1

µA

ILO

Output Leakage Current

VOUT = VSS to VCC

0.1

µA

VIL (Note 1) Input LOW Voltage

-0.5

VCC x 0.3

VIH (Note 1) Input HIGH Voltage

VCC x 0.7

VCC + 0.5

VOL1

Output LOW Voltage

VCC > 3.3V, IOL = 2.1mA

0.4

VOL2

Output LOW Voltage

2V < VCC ≤ 3.3V, IOL = 1mA

0.4

VOL3

Output LOW Voltage

VCC ≤ 2V, IOL = 0.5mA

0.4

VOH1

Output HIGH Voltage

VCC > 3.3V, IOH = -1.0mA

VCC - 0.8

VOH2

Output HIGH Voltage

2V < VCC ≤ 3.3V, IOH = -0.4mA

VCC - 0.4

VOH3

Output HIGH Voltage

VCC ≤ 2V, IOH = -0.25mA

VCC - 0.2

VOLRS

Reset Output LOW Voltage

IOL = 1mA

0.4

Power-Up Timing

SYMBOL

PARAMETER

MIN

MAX

UNIT

tPUR (Note 2) Power-up to read operation

tPUW (Note 2) Power-up to write operation

Capacitance TA = +25°C, f = 1MHz, VCC = 5V

SYMBOL

TEST

MAX

UNIT

CONDITIONS

COUT (Note 2) Output capacitance (SO, RESET, RESET)

VOUT = 0V

CIN (Note 2) Input capacitance (SCK, SI, CS, WP)6

VIN = 0V

NOTES:

1. VIL min. and VIH max. are for reference only and are not tested.

2. This parameter is periodically sampled and not 100% tested.

X5083

X5083PI Datasheet(PDF) 13 Page - Intersil Corporation

X5083PI Datasheet(HTML) 13 Page - Intersil Corporation

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Datasheet Descarga

Enlace URL