S3 Series

Control Panel

Small Addressable

Fire Alarm Control Panel

GAMEWELL-FCI

12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118

Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use.

©2016 by Honeywell International Inc. All rights reserved.

www.gamewell-fci.com

9021-60730 Rev. G page 1 of 4

FDNY:

COA-#6162

MEA

S1869

SIGNALING

7165-1703:0176

City of

Chicago

Approved

of Compliance

VMA-45894-02C

APPROVED

FM

Description

The Gamewell-FCI, S3 Series Intelligent Fire Alarm Control

Panel provides the latest innovative high-end processing

power. The S3 Series is a digital, microprocessor-based

system that offers a simple, intuitive solution for the small

to mid-sized fire alarm applications.

In standalone or network configurations, the S3 Series

complies with most fire alarm application requirements. It

supports either of the following types of networks.

•

Up to 64 nodes using the 7100 Series panel.

•

panels.

Use either twisted-pair wire or fiber-optic to network panels

at a high-speed 625K baud ARCNET network bus.

With flexible Boolean logic, intelligent detection, and Ether-

net connectivity, this system provides power and versatility

that surpasses comparable, small addressable fire alarm

systems.

The basic S3 Series consists of an SLP (Smart Loop

Panel) main board, LCD-SLP touchscreen display, SLC

loop personality modules, and 7 amp power supply. The

SLP provides either one or two SLC loops in Class A or B

configuration that supports either of the following protocols:

•

protocol. If you add a second loop module, it increases

the maximum device count to 636 devices.

•

Up to 126 devices per loop using the Apollo protocol. If

you add a second loop module, it increases the maxi-

mum device count to 252 devices.

Four Class B or two Class A NACs can be wired and syn-

chronized using the System Sensor, Cooper-Wheelock, or

Gentex strobes. To retrofit the SLP on the existing audible/

visual appliances, the on-board Electronic EOL (EEOL)

automatically adjusts to the EOL resistor in the field.

A 4.3"

(10.92 cm) color touchscreen display screen shows

the following:

•

Events on the system

•

Status of analog addressable devices

•

Complete diagnostic fault codes/messages

•

Five programmable function buttons with LED status for

accessibility to the following functions:

- Disable/Enable

- Trouble Acknowledge

- Bypass Output

- Alarm Acknowledge

- Lamp Test

- Custom-defined

E3 Series®, System Sensor® and FocalPoint® are registered trademarks of Honeywell

International Inc.

UL® is a registered trademark of Underwriters Laboratories Inc.

Features

S3 Series

•

•

IBC Seismic Certified.

•

Allows one SLC loop (expandable to two loops) that

supports either System Sensor or Apollo devices in

Class A or Class B (Style 4, 6 or 7).

•

System Sensor supports up to 318 intelligent

devices and each SLC loop supports the following.

- up to 159 detectors.

- up to 159 modules (expandable to 636 maximum

per panel).

•

Apollo supports up to 126 intelligent detectors and

modules per SLC. (Expandable to 252 maximum per

panel).

•

Includes a high resolution (4.3”)

(10.92 cm) color touch-

screen display.

•

Supports a network system of up to 122 nodes

(includes 7100 Series).

•

Provides 7.0 amp power supply (120VAC or 240VAC).

•Includes four Class B or two Class A built-in Notification

Appliance Circuits (NAC). Provides selectable System

Sensor, Cooper-Wheelock, or Gentex strobe synchroni-

zation.

•

Supports up to 32 serial annunciators (LCD, LED-only,

LED Switch).