PIC16F87 datasheet(170/230 Pages) MICROCHIP

170 / 230 page

PIC16F87/88

DS30487D-page 170

 2002-2013 Microchip Technology Inc.

Supply Current (IDD)(2,3)

PIC16LF87/88

.950

1.3

-40°C

FOSC = 8 MHz

(RC_RUN mode,

Internal RC Oscillator)

.930

1.2

+25°C

VDD = 3.0V

.930

1.2

+85°C

All devices

1.8

3.0

-40°C

VDD = 5.0V

1.7

2.8

+25°C

1.7

2.8

+85°C

Extended devices

2.0

4.0

+125°C

PIC16LF87/88

A

-10°C

FOSC = 32 kHz

(SEC_RUN mode,

Timer1 as clock)

914

A

+25°C

VDD = 2.0V

A

+70°C

PIC16LF87/88

A

-10°C

A

+25°C

VDD = 3.0V

A

+70°C

All devices

A

-10°C

A

+25°C

VDD = 5.0V

A

+70°C

18.2

DC Characteristics: Power-Down and Supply Current

PIC16F87/88 (Industrial, Extended)

PIC16LF87/88 (Industrial) (Continued)

PIC16LF87/88

(Industrial)

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

 TA  +85°C for industrial

PIC16F87/88

(Industrial, Extended)

Standard Operating Conditions (unless otherwise stated)

Operating temperature

-40°C

 TA  +85°C for industrial

-40°C

 TA  +125°C for extended

Param

No.

Device

Typ

Max

Units

Conditions

Legend:

Shading of rows is to assist in readability of the table.

Note

The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with

the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that add delta

current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).

The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading

and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on

the current consumption.

The test conditions for all IDD measurements in active operation mode are:

OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD;

MCLR = VDD; WDT enabled/disabled as specified.

For RC oscillator configurations, current through REXT is not included. The current through the resistor can be estimated

by the formula Ir = VDD/2REXT (mA) with REXT in k

.

PIC16F87 Datasheet(PDF) 170 Page - Microchip Technology

PIC16F87 Datasheet(HTML) 170 Page - Microchip Technology

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL