M38047F8HKP datasheet(103/387 Pages) RENESAS

103 / 387 page

1-85

REJ09B0212-0100Z

Rev.1.00

Jan 14, 2005

3804 Group (Spec.H)

HARDWARE

FUNCTIONAL DESCRIPTION

q Software Commands

Table 15 lists the software commands.

After setting the CPU rewrite mode select bit to “1”, execute a soft-

ware command to specify an erase or program operation.

Each software command is explained below.

• Read Array Command (FF16)

The read array mode is entered by writing the command code

“FF16” in the first bus cycle. When an address to be read is input

in one of the bus cycles that follow, the contents of the specified

address are read out at the data bus (D0 to D7).

The read array mode is retained until another command is written.

• Read Status Register Command (7016)

When the command code “7016” is written in the first bus cycle,

the contents of the status register are read out at the data bus (D0

to D7) by a read in the second bus cycle.

The status register is explained in the next section.

• Clear Status Register Command (5016)

This command is used to clear the bits SR4 and SR5 of the status

tion has ended in an error. To use this command, write the

command code “5016” in the first bus cycle.

• Program Command (4016)

Program operation starts when the command code “4016” is writ-

ten in the first bus cycle. Then, if the address and data to program

are written in the 2nd bus cycle, program operation (data program-

ming and verification) will start.

Whether the write operation is completed can be confirmed by

_____

read status register or the RY/BY status flag. When the program

starts, the read status register mode is entered automatically and

the contents of the status register is read at the data bus (D0 to

D7). The status register bit 7 (SR7) is set to “0” at the same time

the write operation starts and is returned to “1” upon completion of

the write operation. In this case, the read status register mode re-

mains active until the read array command (FF16) is written.

Table 15 List of software commands (CPU rewrite mode)

The RY/BY status flag of the flash memory control register is “0”

during write operation and “1” when the write operation is com-

pleted as is the status register bit 7.

At program end, program results can be checked by reading the

status register.

Fig. 82 Program flowchart

Command

Program

Clear status register

Read array

Read status register

First bus cycleSecond bus cycle

FF16

7016

5016

4016

Write

XSRD

Read

Write

(Note 1)

WA (Note 2)

WD (Note 2)

Block erase

2016

Write

D016

WriteBA (Note 3)

ModeAddress

Data

(D0 to D7)

(Note 4)

Notes 1: SRD = Status Register Data

2: WA = Write Address, WD = Write Data

3: BA = Block Address to be erased (Input the maximum address of each block.)

4: X denotes a given address in the User ROM area.

Cycle number

Data

Start

Write “4016”

Read status register

Program

completed

YES

Write address

Write data

SR4 = “0”?

Program

error

YES

SR7 = “1”?

RY/BY = “1” ?

Write

M38047F8HKP Datasheet(PDF) 103 Page - Renesas Technology Corp

M38047F8HKP Datasheet(HTML) 103 Page - Renesas Technology Corp

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 ...More

Datasheet Descarga

Enlace URL