Motor de Búsqueda de Datasheet de Componentes Electrónicos |
|
NE555 Datasheet(PDF) 7 Page - NXP Semiconductors |
|
|
NE555 Datasheet(HTML) 7 Page - NXP Semiconductors |
7 / 7 page Philips Semiconductors Linear Products Product specification NE/SA/SE555/SE555C Timer August 31, 1994 352 TYPICAL APPLICATIONS DURATION OF TRIGGER PULSE AS SEEN BY THE TIMER VCC VCC 10k 2 555 .001 µF NOTE: All resistor values are in Ω Figure 1. AC Coupling of the Trigger Pulse 1 SWITCH GROUNDED AT THIS POINT OVOLTS 1/3 VCC VCC Trigger Pulse Width Requirements and Time Delays Due to the nature of the trigger circuitry, the timer will trigger on the negative going edge of the input pulse. For the device to time out properly, it is necessary that the trigger voltage level be returned to some voltage greater than one third of the supply before the time out period. This can be achieved by making either the trigger pulse sufficiently short or by AC coupling into the trigger. By AC coupling the trigger, see Figure 1, a short negative going pulse is achieved when the trigger signal goes to ground. AC coupling is most frequently used in conjunction with a switch or a signal that goes to ground which initiates the timing cycle. Should the trigger be held low, without AC coupling, for a longer duration than the timing cycle the output will remain in a high state for the duration of the low trigger signal, without regard to the threshold comparator state. This is due to the predominance of Q15 on the base of Q16, controlling the state of the bi-stable flip-flop. When the trigger signal then returns to a high level, the output will fall immediately. Thus, the output signal will follow the trigger signal in this case. Another consideration is the “turn-off time”. This is the measurement of the amount of time required after the threshold reaches 2/3 VCC to turn the output low. To explain further, Q1 at the threshold input turns on after reaching 2/3 VCC, which then turns on Q5, which turns on Q6. Current from Q6 turns on Q16 which turns Q17 off. This allows current from Q19 to turn on Q20 and Q24 to given an output low. These steps cause the 2 µs max. delay as stated in the data sheet. Also, a delay comparable to the turn-off time is the trigger release time. When the trigger is low, Q10 is on and turns on Q11 which turns on Q15. Q15 turns off Q16 and allows Q17 to turn on. This turns off current to Q20 and Q24, which results in output high. When the trigger is released, Q10 and Q11 shut off, Q15 turns off, Q16 turns on and the circuit then follows the same path and time delay explained as “turn off time”. This trigger release time is very important in designing the trigger pulse width so as not to interfere with the output signal as explained previously. |
Número de pieza similar - NE555 |
|
Descripción similar - NE555 |
|
|
Enlace URL |
Política de Privacidad |
ALLDATASHEET.ES |
¿ALLDATASHEET es útil para Ud.? [ DONATE ] |
Todo acerca de Alldatasheet | Publicidad | Contáctenos | Política de Privacidad | Intercambio de Enlaces | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |